Power Puck®
- Last sold in mid 2000’s, these are two button, four-band instruments with black numbers on a LCD display
- Service and support on this product is no longer available (December 31, 2019)
- Contact EIT 2.0 LLC to discuss replacement options (PowerMAP II, Power Puck II or Power Puck II Profiler)
- Brochure, User Manual
UviCure® Plus
- Last sold in mid 2000’s, these are two button, single-band instruments with black numbers on a LCD display
- Service and support on this product is no longer available (December 31, 2019)
- Contact EIT 2.0 LLC to discuss replacement options (UviCure Plus II, UviCure Plus II Profiler)
- Brochure, User Manual
UV PowerMAP® and UV MAP Plus®
The PowerMAP and UV Map Plus were discontinued in 2016 because of obsolete components. The PowerMAP has been replaced by the new PowerMAP II. Other replacement options include the EIT 2.0 LLC Power Puck II Profiler (four band) or UviCure Plus II Profiler (single band)
EIT 2.0 LLC plans to support the PowerMAP and UV Map Plus systems through December 31, 2022. Repairs may be limited based on component availability.
PowerMAP manual, PowerMAP brochure, PowerMAP Optics locations, PowerMap Troubleshooting guide
3DCure®
Sales of the 3D Cure System ended December 31, 2019. EIT 2.0 LLC will support existing 3D Cure Sensors in the field through December 31, 2021. The EIT 2.0 LLC 3D Cure software was designed for Windows 7 and it will not be updated for Windows 10.
3DCure is a unique system for measuring the energy density (J/cm²) and peak irradiance (W/cm²) accurately on large and/or multi-dimensional objects. Up to 32 sensors in any combination of UV bandwidths can be daisy-chained together and placed on every exposure surface in order to feed information back from up to 32 varied measurement points. Data is transferred to you PC via Cure 3D® software. Information can then be exported to a spreadsheet to allow analysis.
PALM Probe®
The PALM Probe was last sold in 2016 and was discontinued due to obsolete components. EIT 2.0 LLC plans to support this product through December 31, 2021. Repairs subject to component availability.
UviMAP
- Last sold in the late 1990’s, all service and support on this product stopped December 31, 2018.
- Contact EIT 2.0 LLC for replacement options (PowerMAP II, UviCure Plus II Profiler, Power Puck II Profiler)
- Brochure, Operation manual
UviCure (M 365)
- Precursor to UviCure Plus 365
- EIT 2.0 LLC stopped production in the early 1990’s
- All service and support on this product stopped on December 31, 2018
- Brochure, Operating manual
UviRad
- This unit dates to 1986 and was last sold in 2010
- All service and support ended December 31, 2018
- Contact EIT 2.0 LLC for replacement options (Low power UviCure Plus II)
- Operating Instructions
UV Power Puck II Flash
- Last sold this unit in 2014, all service and support on this unit ended June 30, 2018
- Brochure, User Manual
EIT 2.0 LLC Thermal Products
The TIP™1K is no longer stocked as a commercially available “off the shelf” product. Please contact EIT 2.0 LLC to inquire about custom builds and/or for service and support on TIP™ 1K units manufactured by EIT 2.0 LLC and sold by either EIT 2.0 LLC or Tutco Farnam Custom Products.
TIP1K Brochure, TIP1K Manual, Thermal Process Control Article
Online UV Intensity Display Module
The EIT 2.0 LLC Online UV Intensity Display Module has a display (0-199%) and 0-10V analog output proportional to the UV intensity. The display/voltage output can be adjusted to “100%” when conditions are ideal (new lamp, clean reflectors). The Display Module also allows the user to set a low UV limit threshold alarm. An LED on the front panel of the display will be green when “above” the limit and red when “below” the low level set. The system requires 24 AC/DC power. Contact EIT 2.0 LLC for Commercial Off The Shelf (COTS) options that can be used with the EIT 2.0 LLC DIN Rail.